• English (UK)
  • Deutsch
  • Login
Login
  • Forgot your password?
  • Forgot your username?
Close
  • Home
  • Products
    • Product Overview
    • Prices
    • Register for a login
  • About us
    • Company History
    • Environment
  • Usefull information
    • Good to know
    • Download
  • Contact
    • Contact addresses
    • Legal notice
    • Terms and Conditions
Home » Home

Products

  • I/O Components
    • Accessories
    • BACnet I/O Modules
    • CAN I/O Modules
  • Installation Contactors
    • Mono Stable - Humm free
  • Relay Technology
    • Control devices for lights
    • Coupling Modules and Industrial Relays
    • Electronic Timers
    • Monitoring relays
  • Signal Converter / Isolation Amplifier
    • Compact Form
    • Industrial housing - multi voltage
    • Monitoring modules
    • Slim 6mm housing

Manual operation makes life easier

swiss madeIn building automation as well as in process control, it is very practical to switch a relay contact or, with an analogue value transmitter or a manipulated variable transmitter, an analogue signal of 0 - 10 V or 0 - 20 mA on and off without a controller during commissioning or servicing. This means switching a valve, pump, heating or ventilation in manual mode or operating a valve, mixing flap, temperature values, etc. with an analogue signal.
If the controller should fail, emergency operation can be established with the manual operation and long downtimes can be avoided.
In order to ensure that everything is switched to automatic when leaving the plant, the Auto - OFF - MAN switches are equipped with an additional potential-free contact. This transmits the operating state of the coupling components to the controller.

kbd-1

Link to the Swiss Made modules in the webshop

The new Universal-Transmitter RT45000

RT45000One for everything: The new Universal-Transmitter RT45000 for Pt, Ni, KTY and TC Standard-Sensors. MV, R and Potentiometer-Measuring, programmable via DIP and USB.

The programmable Universal Transmitter RT 45000 is used for measure industrial process signals. It converts Pt, Ni, KTY or TC sensor signals as well as poti, resistor or mV signals on input to standard signals.

Due to the easy configuration via USB interface and the calibrated range selection per DIP switch the Transmitter is suitable for flexible use.
The Simulation Function, switchable on front side, simulates an output reference signal for testing and adjusting of the complete signal path. With der Teach-In Function the measuring range limits can be set during operation.

With the USB Programming-Kit RELMATICset the Transmitter can be configured and all data can be stored by a PC. In mode of programming no additionally auxiliary power is required.

The auxiliary power can be supplied via the connection terminals or via the optional In-Rail-Bus connector. The status of power supply and sensor connection will be displayed by a LED on front.

Click here to see this product in the Online-Shop

The new RN21000

RN21000The new signal splitter RN21000 is used for dividing an analogue signal into two separate outputs. Each output can be configured seperatly. The device has a 4-port isolation.

The Signal Splitter/Repeater RN 21000 is used for isolation, conversion and distribution of 0/4 ... 20 mA, 0/1 ... 5 V and 0/2 … 10 V standard signals. The measuring input supplies also 2-wire transmitters with power.

The input and two isolated outputs can be easily configured by using DIP switch. Due to the calibrated range selection no further adjustment is necessary.

The auxiliary power can be supplied via the connection terminals or via the optional In-Rail-Bus connector. A green LED on the front of the unit has been provided to monitor the power supply

Click here to see this product in the Online-Shop

More Articles...

  1. Installations-Schütze EN
  2. TOV-Control EN

Page 1 of 2

  • Start
  • Prev
  • 1
  • 2
  • Next
  • End

Copyright © 2018 Relmatic AG. All Rights Reserved.